How To Cut And Polish Boulder Opal

How To Cut And Polish Boulder OpalIn this guide we will show you some tops and tricks to cutting Australian Boulder Opal. Boulder Opal is Opal that has a hard backing made of Ironstone with precious Opal. The precious Opal can be a thin layer on top of the Ironstone or it can be intertwined within the Ironstone.

Australian boulder opal from Queensland is a fascinating stone. Cutting boulder opalsis a challenge but the results are usually breathtaking.Becausethe material is so hard it isdifficultto make a cutting mistake so this type of material is good for novice cutters as well as experienced cutters.download a poster

Lets get stuck into a basic overview on how to cut and polish Boulder opal.

Equipment you Will Need

  • Dop sticks
  • Dop wax or strong glue
  • Trim saw with thin
  • Blade (with rim thickness approximately 0.02”)
  • Diamond grinding wheels 80, 220, 600, 1200, and 3000 grits
  • Cutting equipment
  • Rough leather
  • Polishing disk
  • Tin oxide polish
  • Lamp with 100-watt bulb
  • Safety glasses
  • Dust mask
  • Old work clothes
  • Water supply

Preparation Of The Rough Material

1. Hand Pick Your Opals

Pick out the days work of opals you wish to polish. It is moreefficientto cut multiple stones atthe same time as you will only need toset-upthe machine once. Selecting boulder opal to work with is a skill in itself. Like working with any other rough material the more you know the better. Make sure that the ironstone around the opal is fairly strong and free from cracks. Some reasonably low-grade material is good to start with. You might not end up with a beautiful stone but you can develop your systematic skill enough that you will be capable of cutting that attractive stone in any way you want.

Pick out the days worth of wok

2. Study The Opal And Saw It Up

Look for the pattern of the ironstone to provide you some clues about the path in which the seam will run. When Opal occurs in ironstone, it has flat and straight parallel lines along the matrix. There is a better chance that the opal will track this line.If the rough is soaked in water let it dry first so you can see where the Opal is running. Check for cracks running across the stone and again look for any imperfections throughout the stone. If there are cracks running through the stone you can use the saw to split the opal down the crack. This will avoid any problems later on.

Most of the rough material you will buy has already been slabbed up so you can clearly see the Opal layer. If they material iscompletelyrough and you cannot easily see the Opal you will need to saw the stone to expose the Opal layer.

The saw blade should always be under water. Use plenty of water to keep the dust down and the Opal cool. Never cut dry as opal will heat quickly and crack.

Use Water On Saw Blade when cutting Opalslab up the opal on a saw bladeOpal cut in halfsaw after cutting boulder opal

3. Use Coarse Cutting Wheel To Remove Material

Now is the fun part. You will need a set of old clothes because it’s going to get dirty. Now that you have a fair idea of the course in which the seam will run it is time to rub it down. Having a combination of 80 and 220 grit wheel can make rubbing down the Opal much easier. use the coarse grit wheel to remove material quickly. Try not to get too close to the line of opal. The layer of opal can be unpredictable so try and stay just above the layer.

Rub down the ironstone opalRub down the opal to the color bar

4. Study And Familiarize Yourself With The Opal

Now it is time to familiarize the Opal. You must decide which surface is going to be the top. Base your judgement on the form and layer of the opal, the coloring, brightness, and width of the surrounding material.

Try to make sure that the material directly below the Opal is as dark as possible. This dark setting will create the colors of the opal to stand out. If there is a thin cover of dark potch between the row of Opal and the ironstone it will make the stone pop. You must try to cut the stone so that this black coating will give the backdrop for your stone.

This kind of stone is referred to as a black boulder and can be quite radiant. It is also important that the boulder opal consists of a solid base. If the ironstone on other surface of opal is too lean, it will not offer the strength that is needed for the bottom of your stone.

Familirsie yourself with the opal

5. Rub Away The Ironstone

Now that you know which way the opal will face use the 220 and 280 grit wheel. You must not come into contact with the opal once you decided to use the 220-grit wheel as it can rapidly eliminate quite a bit of the vibrant materials.

It is also advisable to use light pressure ranging from 220-grit wheel as you getting closer to the opal. You must keep on eliminating ironstone until you are just about to display opal in one part of the surface. Occasionally, before you reach the opal, you will even notice that the color of the ironstone will change.

exposed color bar in opal

6. Rub Down To Expose The Opal

Switch over to the 600-grit wheel in order to expose some opal. At this period, you are not trying to eliminate all of the ironstone from the surface. You can do it by going back and forth between the 600-grit wheel with medium pressure. Use light pressure on the 280-grit wheel. Once you establish how the layer of opal operates, you can stop working on the top.

Cutting The Opal And Polishing

Polishing wheels start at 120 grit diamond than rubber wheels 400 grit / 600 grit / 1400 grit before final polish.

1. Dop The Opal

First we need to get the stone onto a dop stick. When the stone is on the dop stick it is easier to manoeuvre and shape. Use the 220-grit wheel and flatten its reverse side. tone.

opals ona  dop stickopals on a dop stick

The two most common ways to dop an opal is with Glue or using wax.


The base of the stone must clean and dry. Apply one or two drops of glue to the dop sticks. Pre-heat the opal by resting it on the border of the dop pot for not more than 30 seconds.

Use light pressure to push the opal into the dop stick. The glue will dry after about 30 minutes.

Glue for dop sticksglued on Opals to the dop stick


If the reverse side of the opal is spongy and the glue does not work you may use wax as an alternative. Heat the Opal and drop melted wax onto the opal before applying it the dop sticks. You must make sure the dop sticks have a sufficient amount of melted wax on them.

Dop sticks for opalsdopping opals onto a dop stick with wax

2. Setup Your Watering System

This is the step where you can cut the opal. If you’re using a device that re-circulates its water such as the water that is sprayed up onto the wheels, you can dripped down into a pan, then forced from that pan and sprayed up onto the wheels once more. Change the water and make the pans dirt-free regularly.

water setup for cutting opalwater seup for rough opal

3. Pre-Form - Make The Decisions

At this point you are require to make some significant decisions. Look at the general appearance of your stone, both the ironstone and opal. Their combination can be relatively beautiful.

Keep on eliminating ironstone with the 600-grit wheel. Think about keeping the stone moving. The 600-grit wheel can still reduce opal and create smooth spots and scrapes. You can do a lot of things during this stage of cutting. You are eliminating scratches from previous stages.

Then, eliminating ironstone from the surface, and building the surface and form of the stone is pleasing to the eye. Check your stone and observe what it shows you. You might require going back the 280-grit wheel and changing its form. Once you have eliminated the big scratches and are pleased with the look, go to the 1200-grit wheel.

shaping a boulder opalshaping boulder opal

4.FinalizeThe Shape And Expose The Opal

In this step, the 1200-grit wheel will eliminate almost all noticeable scratches. It will not do much to modify the form of your stone, but it can better its form. Use reasonable pressure and make sure the stone is continually moving.

Stop regularly and clean up your stone to verify the progress and ensure that the scratches are completely vanishing.

Once you have removed the noticeable scratches, shift to the 3000-grit wheel, or if you’re not using a 3000-grit wheel, begin to clean your stone. If your device consists of a 14,000-grit wheel, it is advisable not to cut boulder opal. This wheel begins often with scratches.

shaping and pre polish on boulder opalshaping and pre polish on opal

5. Final Polish

The next phase is the process of polishing. In order to make it shine, you can use tin oxide for cleaning the foam-backed rough leather pad. Just lightly soaked it with water through the use of a spray bottle and with the running device running and spinning pad.

Also, use a brush to apply a well-stirred combination of water and tin oxide onto the moist pad. From here, the water mixture as well as, the tin oxide must be thin enough so that it does not clomp, and has the uniformity of thin gravy.

lapsa polishing compound

Just keep the opals stirring by turning the dop stick between your fingers and by varying the position of the pad. Do not allow the opal to get too hot. Sometimes, the coarse leather pad can seize your stone and pull it out of your hands. This is usually because the pad has dried out or if the stone has a rough surface or even pointed edges.

polish boulder opalpolish boulder opalpolish boulder opalpolish boulder opal

6. A Note On Matrix Boulder opal

if you are decide to polish a matrix opal, you can pursue the same process. The opal usually polishes, but the ironstone matrix will be dry. A helpful method is to clean the opal as explained, and then permit the pad dry faintly. Use more force while you maintain the stone moving, so that you can sense the stone to get even warm.

Remember that you are cleaning the matrix, not the opal spots of your stone. Be careful while heating the stone along your polishing pad, which can develop the finish of the matrix, but be, reminded that too much heat can break the opal. This method needs a bit of practice, but the outcomes can be worth it.

7. Finish The Back Of The Stone

Lastly you can do the finishing of the back. When you are completed polishing take the stone from its dop stick. You can use light to standard pressure for roughly about 220-280 for your grit wheel in order to take out any residue of the doping matter.

You must keep the stone flat against the wheel, but turn it slightly so that scratches will be avoided on its back. At this point, select what you prefer for the specific size of the stone. When you arrived with the suitable thickness, apply the 220 or 280-grit for the wheel that can be help to minimize chipping when setting.

You can either think the opal completed, or get a more finished look by taking the back through the remaining chain of finer wheels. You must cut the back portion of stones by means of 1200 or 3000-grit wheels.

Finished Product

After all of the opals have been cut and polished they can be sorted and graded.

finished opals

Boulder opals make great pendants. All that is needed is a drill press to create a hole in the tip of them. Thread through a leather strap and you have yourself a beautiful boulder Opal necklace.

marking holes for drilling

Handy Tip From An Opal Cutter

Worried about turning your machine on and off with wet hands? Try and glue a dop stick to the power board switch. That way nothing wet ever comes in contact with electricity. Brilliant.

switch board with dop sticks

sign up for free poster

Like Our Blogs? Sign Up For Email Notifications.

Shop For Boulder Rough

Was this article helpful?

10 people found this article helpful
A-Z Of Opals

A-Z Of Opals

A complete list of your favourite Opal from all over the world
19 articles
Did you know?

Did you know?

Check out our fascinating information and articles on all things amazing in the Opal world
17 articles
How To's

How To's

All of your favourite Opal How To's
14 articles


What's trending in the Opal Industry
28 articles
Opal Auctions  Verified Sellers

Opal Auctions Verified Sellers

Opal Auctions sellers who are approved as opal Verified Sellers
3 articles
Opal Information

Opal Information

Information about Opal and its colourful history
72 articles
Opal Stories

Opal Stories

Feel like reading a yarn or two?
5 articles
Technical Opal Information

Technical Opal Information

All there is to know about Opals including Black Opals, Ethiopian Opals & Boulder Opal
8 articles


Feedback from our VIP customers
5 articles

Hello! Opal Auctions is an international marketplace offering Opal Stones, Rough & Jewelry from professional Opal cutters, dealers & miners. Register for $10 off your first purchase.